編集

次の方法で共有


Set-ExoPhishSimOverrideRule

This cmdlet is available only in the cloud-based service.

Use the Set-ExoPhishSimOverrideRule cmdlet to modify third-party phishing simulation override rules to bypass Exchange Online Protection filtering. For more information, see Configure the advanced delivery policy for third-party phishing simulations and email delivery to SecOps mailboxes.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Set-ExoPhishSimOverrideRule
   [-Identity] <ComplianceRuleIdParameter>
   [-AddDomains <MultiValuedProperty>]
   [-AddSenderIpRanges <MultiValuedProperty>]
   [-Comment <String>]
   [-Confirm]
   [-DomainController <Fqdn>]
   [-RemoveDomains <MultiValuedProperty>]
   [-RemoveSenderIpRanges <MultiValuedProperty>]
   [-WhatIf]
   [<CommonParameters>]

Description

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Get-ExoPhishSimOverrideRule | Set-ExoPhishSimOverrideRule -AddDomains blueyonderairlines.com -RemoveSenderIpRanges 192.168.1.55

This example modifies the (presumably only) phishing simulation override rule with the specified settings.

This example modifies the phishing simulation override rule with the specified settings.

Example 2

Set-ExoPhishSimOverrideRule -Identity "_Exe:PhishSimOverr:6fed4b63-3563-495d-a481-b24a311f8329" -AddDomains blueyonderairlines.com -RemoveSenderIpRanges 192.168.1.55

This example modifies the specified phishing simulation override rule with the specified settings.

Parameters

-AddDomains

The AddDomains parameter specifies an existing entry to add to the list of email domains that are used by the third-party phishing simulation.

You can specify multiple values separated by commas. A maximum of 20 entries are allowed in the list.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-AddSenderIpRanges

The AddSenderIpRanges parameter specifies an existing entry to add to the list of source IP addresses that are used by the third-party phishing simulation. Valid values are:

  • Single IP address: For example, 192.168.1.1.
  • IP address range: For example, 192.168.0.1-192.168.0.254.
  • Classless InterDomain Routing (CIDR) IP address range: For example, 192.168.0.1/25.

You can specify multiple values separated by commas.

A maximum of 10 entries are allowed in the list.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-Comment

The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".

Type:String
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-DomainController

This parameter is reserved for internal Microsoft use.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-Identity

The Identity parameter specifies the phishing simulation override rule that you want to modify. You can use any value that uniquely identifies the rule. For example:

  • Name
  • Id
  • Distinguished name (DN)
  • GUID

Use the Get-ExoPhishSimOverrideRule cmdlet to find the values. The name of the rule uses the following syntax: _Exe:PhishSimOverr:<GUID\> [sic] where <GUID> is a unique GUID value (for example, 6fed4b63-3563-495d-a481-b24a311f8329).

Type:ComplianceRuleIdParameter
Position:1
Default value:None
Required:True
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Online

-RemoveDomains

The RemoveDomains parameter specifies an existing entry to remove from the list of email domains that are used by the third-party phishing simulation.

You can specify multiple values separated by commas.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-RemoveSenderIpRanges

The RemoveSenderIpRanges parameter specifies an existing entry to remove from the list of source IP addresses that are used by the third-party phishing simulation. Valid values are:

  • Single IP address: For example, 192.168.1.1.
  • IP address range: For example, 192.168.0.1-192.168.0.254.
  • Classless InterDomain Routing (CIDR) IP address range: For example, 192.168.0.1/25.

You can specify multiple values separated by commas.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Online