Set-SecOpsOverridePolicy

Reference

Module:: ExchangePowerShell

Applies to:: Exchange Online, Security & Compliance, Exchange Online Protection

This cmdlet is available only in the cloud-based service.

Use the Set-SecOpsOverridePolicy cmdlet to modify SecOps mailbox override policies to bypass Exchange Online Protection filtering. For more information, see Configure the advanced delivery policy for third-party phishing simulations and email delivery to SecOps mailboxes.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Set-SecOpsOverridePolicy
   [-Identity] <PolicyIdParameter>
   [-AddSentTo <MultiValuedProperty>]
   [-Comment <String>]
   [-Confirm]
   [-DomainController <Fqdn>]
   [-Enabled <Boolean>]
   [-Force]
   [-RemoveSentTo <MultiValuedProperty>]
   [-WhatIf]
   [<CommonParameters>]

Description

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Set-SecOpsOverridePolicy -Identity SecOpsOverridePolicy -AddSentTo secops2@contoso.com

This example modifies the SecOPs mailbox override policy with the specified settings.

Parameters

-AddSentTo

The AddSentTo parameter specifies an entry to add to the existing list of SecOps mailbox email addresses. Groups are not allowed.

You can specify multiple values separated by commas.

Type:	MultiValuedProperty
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Security & Compliance, Exchange Online Protection

-Comment

The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".

Type:	String
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Security & Compliance, Exchange Online Protection

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

Type:	SwitchParameter
Aliases:	cf
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Security & Compliance, Exchange Online Protection

-DomainController

This parameter is reserved for internal Microsoft use.

Type:	Fqdn
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Exchange Online Protection

-Enabled

The Enabled parameter specifies whether the policy is enabled. Valid values are:

$true: The policy is enabled. This is the default value.
$false: The policy is disabled.

Type:	Boolean
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Security & Compliance, Exchange Online Protection

-Force

The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.

You can use this switch to run tasks programmatically where prompting for administrative input is inappropriate.

Type:	SwitchParameter
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Online, Exchange Online Protection

-Identity

The Identity parameter specifies the SecOps override policy that you want to modify. You can use any value that uniquely identifies the policy. For example:

Name
Id
Distinguished name (DN)
GUID

Type:	PolicyIdParameter
Position:	0
Default value:	None
Required:	True
Accept pipeline input:	True
Accept wildcard characters:	False
Applies to:	Exchange Online, Security & Compliance, Exchange Online Protection

-RemoveSentTo

The RemoveSentTo parameter specifies an entry to remove from the existing list of SecOps mailbox email addresses. Groups are not allowed.