question

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 asked ·

Unable to join domain Network path not found

I have a AD on an OVH server with WS2019 installed.
When I try to join the domain, I have the following error message: Network Path was not found
The server's ip is static, the client has the server as primary DNS.
I can ping the server with the ip and I can ping the domain
I disabled ipv6 on client and server
The server's primary DNS is his public ip and the secondary is 127.0.0.1
I configured the DNS so it

windows-active-directory
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered ·

Is this a single domain controller? Try restarting the Network Location Awareness service.

--please don't forget to Accept as answer if the reply is helpful--






·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 answered ·

I don't know if this can help but I get a warning when I start the server :

The DNS server is waiting for Active Directory Domain Services (AD DS) to signal that the initial synchronization of the directory has been completed. The DNS server service cannot start until the initial synchronization is complete because critical DNS data might not yet be replicated onto this domain controller. If events in the AD DS event log indicate that there is a problem with DNS name resolution, consider adding the IP address of another DNS server for this domain to the DNS server list in the Internet Protocol properties of this computer. This event will be logged every two minutes until AD DS has signaled that the initial synchronization has successfully completed.

·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 answered ·

Yes, there is only one DC. I tried to restarting this service but it doesn't change anything

·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered ·

Please run;

Dcdiag /v /c /d /e /s:%computername% >c:\dcdiag.log
repadmin /showrepl >C:\repl.txt
ipconfig /all > C:\dc1.txt
netsh advfirewall monitor show currentprofile>C:\DC1profile.txt
ipconfig /all > C:\problemworkstation.txt
set > C:\problemworkstationvars.txt
netsh advfirewall monitor show currentprofile>C:\workstationprofile.txt
C:\Windows\debug\netsetup.log

then put unzipped text files up on OneDrive and share a link.



·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 answered ·

the link:
https://1drv.ms/u/s!ArmCqH2m7DyipUT-30CveHg7KXBK?e=zMS6t8
I runed the commands on the DC

·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered ·

1). Start a Command Prompt (cmd.exe) RunAs administrator
2). Change the folder to the WMI folder:

CD %windir%\system32\wbem

3). Reregister all the Windows Management Instrumentation DLLs:

For /f %s in ('dir /b /s *.dll') do regsvr32 /s %s

4). Reregister the MOF files.

for /f %s in ('dir /b .mof .mfl') do mofcomp %s

5). Type the following command to make sure that the provider host is registered correctly:

wmiprvse /regserver

6). Reboot

The workstation files appear to have come from the server.

If problems persist then put up a new set of files to look at.


·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 answered ·

I runned your commands, it didn't change anything. I pushed on the drive the new file

·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered ·

What's the history here? Did this domain controller just break? If so you may want to consider restoring a recent known good backup.




·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

YannDiasdenovaes-1481 avatar image
0 Votes"
YannDiasdenovaes-1481 answered ·

It didn't. I builded this server today so I don't have backup.
The problem cannot be due to "The DNS server is waiting for Active Directory Domain Services (AD DS) to signal that the initial synchronization of the directory has been completed." ?

·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered ·

That is one issue but usually resolves itself in 10 minutes or so. The bigger issue is
The DFS Replication service failed to register the WMI providers. Replication is disabled until the problem is resolved.

Since a new installation I'd suggest clean installing it, patch fully and try again.




·
10 |1000 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.