question

Michauuu888-8238 avatar image
0 Votes"
Michauuu888-8238 asked Michauuu888-8238 answered

Windows Server 2019 Standard - Active Directory Domain Services

Installed Active Directory Domain Service on Windows Server 2019 Standard and ran into a problem.

After installation, when I open network and internet settings through the Settings application, then I click change card options, I get the following message:

Error: Windows cannot access the specified device, path or file. You may not have the appropriate permission to access the item.

The error points to the path C:\Windows\system32\control.exe and I cannot access the settings of the network adapters from the Settings item. However, when I want to run the Control Panel outside of Settings, it turns on normally.

I also get the same error when in Settings I enter Time and language in the Language submenu for the path C:\Windows\system32\ SystemSettingsAdminFlows.exe, and this application does not start at all, because it is only in the settings and it is not in Control panel. I checked the same error in several other Settings.

To be sure, I did a double AD installation to rule out other factors. My question is, should it be that this service deactivates these settings for me or is there a bug causing me this?



Zainstalowałem usługę domeny Active Directory w Windows Server 2019 Standard i natrafiłem na problem.

Po instalacji, kiedy otwieram ustawienia sieci i Internetu przez aplikację Ustawienia, później klikam zmień opcje karty otrzymuję poniższy komunikat:

Błąd: System Windows nie może uzyskać dostępu do określonego urządzenia, ścieżki lub pliku. Możesz nie dysponować odpowiednimi zezwoleniami na uzyskanie dostępu do elementu.

Błąd wskazuje na ścieżkę C:\Windows\system32\control.exe i z pozycji Ustawień nie mogę przejść do ustawień kart sieciowych. Natomiast kiedy chcę uruchomić Panel sterowania poza Ustawieniami to się normalnie włącza.

Ten sam błąd otrzymuję również kiedy w Ustawieniach wejdę w Czas i język w podmenu Język dla ścieżki C:\Windows\system32\SystemSettingsAdminFlows.exe, no i tej aplikacji nie idzie uruchomić w ogóle, gdyż jest tylko w ustawieniach a nie ma jej w Panelu sterowania. Sprawdzałem jeszcze w kilku innych Ustawieniach ten sam błąd.

Dla pewności przeprowadziłem dwukrotną instalację usługi AD, aby wykluczyć inne czynniki. Moje pytanie brzmi, czy tak powinno być, że ta usługa dezaktywuje mi te ustawienia, czy w czymś tkwi błąd, który mi to powoduje?

windows-serverwindows-active-directorywindows-server-2019
5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

cthivierge avatar image
1 Vote"
cthivierge answered cthivierge edited

Are you using the account "Administrator" ?

It seems to be related to a UAC policy. I do have the same issue with a fresh install of Windows Server 2019 (the eval from MSFT)

118335-error-control.png




If you Enable the following parameter... Open Local Security Policy and go to "Local Policies / Security Options / User Account Control: Admin Approval Mode for the Built-in Administrator account.

Reboot the server and try again if it fix the issue.


error-control.png (30.0 KiB)
5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered

My question is, should it be that this service deactivates these settings for me or is there a bug causing me this?

No, not normal, something sounds broken. Existing domain or new domain? Make sure to patch fully before adding roles.

--please don't forget to upvote and Accept as answer if the reply is helpful--







5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

cthivierge avatar image
0 Votes"
cthivierge answered

As @DSPatrick said, it's not normal. Do you have the same issue before installing ADDS role ?
Does the installation is a fresh install of from a Windows image ?

5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

Michauuu888-8238 avatar image
0 Votes"
Michauuu888-8238 answered

No problem before installation and after uninstalling AD DS, all updates are ready. I did this on the new DELL R540 server with the operating system installed. I reinstalled it, but the situation happened again. I remove AD DS the problem disappears.

5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered

New or existing domain? Might also try adjusting UAC down.

--please don't forget to upvote and Accept as answer if the reply is helpful--


5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

Michauuu888-8238 avatar image
0 Votes"
Michauuu888-8238 answered

I have created a new domain. I did the AD DS installation according to the instructions.

5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

DSPatrick avatar image
0 Votes"
DSPatrick answered DSPatrick edited

Ok, we don't know what instructions (not saying this is an issue). Try adjusting UAC level down. Try using new installation media.

--please don't forget to upvote and Accept as answer if the reply is helpful--



5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

Michauuu888-8238 avatar image
0 Votes"
Michauuu888-8238 answered

I checked and the above method works. Thank you for your help.

5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.