Pull DP Package Transfer Manager failed to update the package

Question

question

lalajee asked Mar 3, '22 saldana-msft edited 3 days ago

Pull DP Package Transfer Manager failed to update the package

Hi,

I have pull DP and some of the packages are failing with this massage.

Package Transfer Manager failed to update the package "xxxx05", Version 1 on pull distribution point Pull.DP.COM. This pull distribution point has no sources from which it can download content. We will try again later.

I have Prestage this package on the PUll DP but after 24 hours, it showing under progress with above message.

In PrestageContent.log I can see following message 'Sent xxxx05 package state message to site'

In MECM console under "\Monitoring\Overview\System Status\Status Message Queries\All Status Messages"

I can see the site is receiving the message

Is they anything else I can do to make it as successful

mem-cm-general mem-cm-application

image.png (32.4 KiB)

5 |1600 characters needed characters left characters exceeded

Attachments: Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

Answer 1 · 2022-03-04T09:39:46.813Z

Amandayou-MSFT answered Mar 4, '22 Amandayou-MSFT commented Mar 21, '22

Hi @lalajee，

I test it in my environment by using this following article and it succeed.
https://blog.ctglobalservices.com/configuration-manager-sccm/kea/configuration-manager-2012-prestage-content-on-distribution-points/
Note: Non-Microsoft link, just for the reference.
Please check where the problem is, if there is any other assistance we can provide, please feel free to let us know.

If the answer is the right solution, please click "Accept Answer" and kindly upvote it. If you have extra questions about this answer, please click "Comment".
Note: Please follow the steps in our documentation to enable e-mail notifications if you want to receive the related email notification for this thread.

· 6

5 |1600 characters needed characters left characters exceeded

Attachments: Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

lalajee · Mar 04 at 10:31 AM

I already re-distribute the package to all DPs and still its showing same message for this Pull DP.

When I run
ExtractContent.exe /P:C:\Tools\xxx3.pkgx /C /I

I see following error ArchiveFile::ExtractContent failed; 0x80004005

0 ·

Amandayou-MSFT lalajee · Mar 07 at 09:39 AM

Hi,

Thanks for your reply.

In prestagecontent.log, is there any error about HashFile failed, in the following post, there is the similar error in it, 0x80004005 translates to unspecified function. In this post, someone used the tool to check the hashs, and copied over new copies extractcontent, it worked fine.
Maybe we could try it.

https://www.reddit.com/r/SCCM/comments/2fhlqm/hash_failed_prestaged_content/
Note: Non-Microsoft link, just for the reference.

Best regards,
Amanda

0 ·

lalajee Amandayou-MSFT · Mar 08 at 09:19 PM

In prestagecontent.log log i see following error

ArchiveFile::ExtractContent failed; 0x80004005

0 ·

lalajee Amandayou-MSFT · Mar 08 at 09:30 PM

I selected an small package was having same issue.

I created pre-stage file again and then run below command

extractcontent /P;path to file /F

Then
extractcontent /P;path to file /C /I

Still I see same message

0 ·

Show more comments

question