Enable Service Bus Geo-DR configurations using PowerShell
Azure Service Bus has released AzureRM.ServiceBus PowerShell Module 5.3.0. With this version you can now configure your Geo-paired namespaces for Geo-DisasterRecovery. The cmdlets let you use the Alias and pair your primary and secondary namespaces. You can then failover to your paired namespace specified in your configuration. To learn more about Geo-DR feature for Service Bus, refer to the Azure Service Bus Geo-DR article.
The following script describes the steps of how this can be done. An additional PowerShell and a CLI sample can also be found here.
Before you begin, you'll need the following:
- An Azure subscription. For more information about obtaining a subscription, see purchase options, member offers, or free account.
- Azure PowerShell. For instructions, see Get started with Azure PowerShell cmdlets.
Copy the following cmdlets into a text or .ps1 file. Use Window + X to open PowerShell command prompt with Admin rights. You can also open the PowerShell ISE as Admin and run the following script,
#Step 1 – Login to your Azure subscription Login-AzureRmAccount # Optional – you need this if you do not have the Service Bus module already installed Install-Module AzureRM.ServiceBus #Step 2 – following parameters are used while creating the resources $location1 = “East US” $location2 = “West US” $resourceGroup = “servicebusgeodrresourcegroup” $primarynamespace = “servicebusprimarynamespace1” $secondarynamespace = “servicebussecondarynamespace1” $aliasname = “servicebusalias1” #Step 3 - Create Resource Group New-AzureRmResourceGroup -Name $resourceGroup -Location $location1 #Step 4 - Create Service Bus primary namespace New-AzureRmServiceBusNamespace –ResourceGroupName $resourceGroup -NamespaceName $primarynamespace -Location $location1 -SkuName Premium #Step 5 - Create Service Bus secondary namespace - Copy the ARM ID from the output as you need it later as -PartnerPartnernamespace. It usually starts with /subscriptions... New-AzureRmServiceBusNamespace –ResourceGroupName $resourceGroup –NamespaceName $secondarynamespace -Location $location2 -SkuName Premium #Step 6 – Create an alias and pairs the namespaces New-AzureRmServiceBusGeoDRConfiguration -ResourceGroupName $resourcegroup -Name $aliasname -Namespace $primarynamespace -PartnerNamespace "---ARM ID from step before---" #Optional – you can obtain the alias details using this cmdlet, here you can also check if the provisioning is done. Provisioning state should change from Accepted to Succeeded when any of the below or above operations are completed. Note that after failover you want to add the secondary namespace instead of the primary namespace. Get-AzureRmServiceBusGeoDRConfiguration -ResourceGroup $resourcegroup -Name $aliasname -Namespace $primarynamespace #Optional – you can break the pairing between the two namespaces if you desire to associate a different pairing. Break pair is initiated over primary only Set-AzureRmServiceBusGeoDRConfigurationBreakPair -ResourceGroupName $resourcegroup -Name $aliasname -Namespace $primarynamespace #Optional – create entities to test the meta data sync between primary and secondary namespaces #Here we are creating a queue New-AzureRmServiceBusQueue -ResourceGroupName $resourcegroup -Namespace $primarynamespace -Name “testqueue1” #Optional – check if the created queue was replicated Get-AzureRmServiceBusQueue -ResourceGroupName $resourcegroup -Namespace $secondarynamespace -Name “testqueue1” #Step 7 – Initiate a failover. This will break the pairing and alias will now point to the secondary namespace. Failover is initiated over secondary only Set-AzureRmServiceBusGeoDRConfigurationFailOver -ResourceGroupName $resourcegroup -Name $aliasname -Namespace $secondarynamespace #Step 8 – Remove the Geo-pairing and its configuration. This cmdlet would delete the alias that is associated with the Geo-paired namespaces # Deleting the alias would then break the pairing and at this point primary and secondary namespaces are no more in sync. you need to add the namespacename of either primary or secondary depending on if you failed over or not. Below shows the state after failover. Remove-AzureRmServiceBusGeoDRConfiguration -ResourceGroupName $resourcegroup -Name $aliasname -Namespace $secondarynamespace #Optional – clean up the created resoucegroup Remove-AzureRmResourceGroup -Name $resourcegroup
Enjoy this new tooling capability for Service Bus and please leave us your valuable feedback and comments!