Update-EmailAddressPolicy

This cmdlet is available only in on-premises Exchange. Use the Update-EmailAddressPolicy cmdlet to apply new or updated email address policies to the affected recipients in an on-premises Exchange organization. For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax (https://technet.microsoft.com/library/bb123552.aspx).

Syntax

Update-EmailAddressPolicy
      [-Identity] <EmailAddressPolicyIdParameter>
      [-Confirm]
      [-DomainController <Fqdn>]
      [-FixMissingAlias]
      [-WhatIf]
      [-UpdateSecondaryAddressesOnly]
      [<CommonParameters>]

Description

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet (https://technet.microsoft.com/library/mt432940.aspx).

Examples

-------------------------- Example 1 --------------------------

Update-EmailAddressPolicy -Identity "Northwest Executives"

This example applies the email address policy named Northwest Executives to all affected recipients.

Required Parameters

-Identity

The Identity parameter specifies the email address policy that you want to apply to recipients. You can use any value that uniquely identifies the policy. For example:

  • Name

  • Distinguished name (DN)

  • GUID

Type:EmailAddressPolicyIdParameter
Position:1
Default value:None
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

Optional Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.

  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
-DomainController

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:Fqdn
Position:Named
Default value:None
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
-FixMissingAlias

The FixMissingAlias switch repairs recipients that don't have an alias. The alias is generated based on the Name property of the recipient. You don't need to specify a value with this switch.

You need to use this switch if you receive an error message when you attempt to update the email address policy, global address list, or address list.

Type:SwitchParameter
Position:Named
Default value:None
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016
-UpdateSecondaryAddressesOnly

The UpdateSecondaryAddressesOnly switch parameter specifies that only the proxy email addresses are updated for the recipients. The recipient's primary email address isn't updated. You don't need to specify a value with this switch.

Type:SwitchParameter
Position:Named
Default value:None
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016
-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

Inputs

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types (https://go.microsoft.com/fwlink/p/?LinkId=616387). If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types (https://go.microsoft.com/fwlink/p/?LinkId=616387). If the Output Type field is blank, the cmdlet doesn't return data.