Event ID 1059 — Terminal Services Authentication and Encryption
Applies To: Windows Server 2008
Transport Layer Security (TLS) 1.0 enhances the security of Terminal Services sessions by providing server authentication and by encrypting terminal server communications. The terminal server and the client computer must be correctly configured for clients to make successful remote connections and for TLS to provide enhanced security. For example, a certificate is needed to authenticate a terminal server when SSL (TLS 1.0) is used to secure communication between a client and a terminal server during Remote Desktop Protocol (RDP) connections.
|Product:||Windows Operating System|
|Message:||The Terminal Server authentication certificate configuration data was invalid and the service reset it. If the computer was configured to use a specific certificate, please verify it is available in the certificate store and use the administrative tools to select it again.|
Check the certificate store and configure the terminal server to use the certificate for TLS 1.0 (SSL)
To resolve this issue, do the following:
- Check the certificate store for the certificate that the terminal server is configured to use for TLS 1.0 (SSL).
- Configure the terminal server to use the certificate for TLS 1.0 (SSL).
For information about certificate requirements, see the section "Certificate requirements" later in this topic.
To perform this procedure, you must have membership in the local Administrators group, or you must have been delegated the appropriate authority.
Check the certificate store for the certificate that the terminal server is configured to use for TLS 1.0 (SSL)
To check the certificate store:
- On the terminal server, open the Certificates snap-in for a computer. If you have not already added the Certificates snap-in console, you can do so by doing the following:
- Click Start, click Run, type mmc, and then click OK.
- On the File menu, click Add/Remove Snap-in.
- In the Add or Remove Snap-ins dialog box, in the Available snap-ins list, click Certificates, and then click Add.
- In the Certificates snap-in dialog box, click Computer account, and then click Next.
- In the Select Computer dialog box, click Local computer: (the computer this console is running on), and then click Finish.
- In the Add or Remove snap-ins dialog box, click OK.
- Confirm that the certificates are displayed by logical certificate stores. To do this, on the View menu, click Options, and in the View Options dialog box, confirm that Logical certificate stores is selected.
- In the Certificates snap-in console, in the console tree, expand Certificates (Local Computer), select Personal, and click Certificates.
- In the details pane, check that the certificate that is being used by the terminal server for server authentication and encryption appears in the list of certificates.
- Do one of the following:
- If the certificate appears in the list, complete the steps in "Configure the terminal server to use the certificate for TLS 1.0 (SSL)" later in this topic.
- If the certificate does not appear in the list, complete the steps in "Install a certificate on the terminal server."
Install a certificate on the terminal server
Important: You should only install certificates obtained from trusted sources. Installing an altered or unreliable certificate could compromise the security of any system component that uses the installed certificate.
To install a certificate on the terminal server:
- On the terminal server, locate and then double-click the certificate that you want to install. The certificate might exist on the terminal server or be located on a share.
- If prompted to confirm whether you want to open the certificate file, click Open.
- In the Certificate Properties dialog box, on the General tab, click Install Certificate.
- In the Certificate Import Wizard, on the Welcome page, click Next.
- On the Certificate Store page, do one of the following:
- If the certificate should be automatically placed in a certificate store based on the type of certificate, click Automatically select the certificate store based on the type of certificate.
- If you want to specify where the certificate is stored, select Place all certificates in the following store, and then click Browse. In Select Certificate Store, click the certificate store to use, and then click OK.
- On the Certificate Store page, click Next.
- On the Completing the Certificate Import Wizard page, click Finish.
After you install a certificate, you must specify that it be used by the terminal server, as described in the following procedure.
Configure the terminal server to use the certificate for TLS 1.0 (SSL)
We recommend that you use the Terminal Services Configuration snap-in to specify the certificate that is used by the terminal server for server authentication and encryption. If you use Terminal Services Configuration to attempt to install a certificate that does not meet the certificate requirements, the certificate will not be installed.
To configure the terminal server:
- Open Terminal Services Configuration. To open Terminal Services Configuration, click Start, point to Administrative Tools, point to Terminal Services, and then click Terminal Services Configuration.
- In the details pane, under Connections, right-click the connection (for example, RDP-tcp) and then click Properties.
- On the General tab, click Select.
- In the Select Certificate dialog box, click the certificate that you want to use, and then click OK.
A certificate that is used by the terminal server for server authentication and encryption must meet the following requirements:
- The certificate must be a computer certificate.
- The certificate must have a corresponding private key. The container for the key must be accessible by the NT AUTHORITY\Network Service account.
- The certificate must have an Enhanced Key Usage (EKU) of Server Authentication (188.8.131.52.184.108.40.206.1) or no EKU.
- The following key usage value must be set for the certificate: CERT_KEY_ENCIPHERMENT_KEY_USAGE.
- The certificate has not expired. We recommend that the certificate be valid one year from the date of installation.
When Transport Layer Security (TLS) 1.0 is functioning as expected for server authentication and encryption of terminal server communications, clients can make connections to terminal servers by using TLS 1.0 (SSL).
To verify that the TLS 1.0 (SSL) settings are correctly configured and working properly on the terminal server to provide server authentication and encryption for connections, use Remote Desktop Connection from a client computer to connect to the terminal server. If you can connect to the terminal server and there is a lock symbol in the upper-left corner of the connection bar at the top of the window, TLS 1.0 (SSL) is being used for the connection.
Note: To ensure that the connection bar is displayed when you use Remote Desktop Connection to connect from a client computer, select full-screen mode when configuring Remote Desktop Connection settings.
To select full-screen mode in Remote Desktop Connection:
- Open Remote Desktop Connection. To open Remote Desktop Connection, click Start, click Accessories, and then click Remote Desktop Connection.
- Click Options to display the Remote Desktop Connection settings, and then click Display.
- Under Remote desktop size, drag the slider all the way to the right to ensure that the remote desktop that you plan to connect to is displayed in full-screen mode.