Security Bulletin
Microsoft Security Bulletin MS09-018 - Critical
Vulnerabilities in Active Directory Could Allow Remote Code Execution (971055)
Published: June 09, 2009 | Updated: June 17, 2009
Version: 1.1
General Information
Executive Summary
This security update resolves two privately reported vulnerabilities in implementations of Active Directory on Microsoft Windows 2000 Server and Windows Server 2003, and Active Directory Application Mode (ADAM) when installed on Windows XP Professional and Windows Server 2003. The more severe vulnerability could allow remote code execution. An attacker who successfully exploited this vulnerability could take complete control of an affected system remotely. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights. Firewall best practices and standard default firewall configurations can help protect networks from attacks that originate outside the enterprise perimeter. Best practices recommend that systems that are connected to the Internet have a minimal number of ports exposed.
This security update is rated Critical for all supported editions of Microsoft Windows 2000 Server, and rated Important for supported versions of Windows XP Professional and Windows Server 2003. For more information, see the subsection, Affected and Non-Affected Software, in this section.
The security update addresses the vulnerability by correcting the way that the LDAP service allocates and frees memory while processing specially crafted LDAP or LDAPS requests.
Recommendation. The majority of customers have automatic updating enabled and will not need to take any action because this security update will be downloaded and installed automatically. Customers who have not enabled automatic updating need to check for updates and install this update manually. For information about specific configuration options in automatic updating, see Microsoft Knowledge Base Article 294871.
For administrators and enterprise installations, or end users who want to install this security update manually, Microsoft recommends that customers apply the update immediately using update management software, or by checking for updates using the Microsoft Update service.
See also the section, Detection and Deployment Tools and Guidance, later in this bulletin.
Known Issues. None
Affected and Non-Affected Software
The following software have been tested to determine which versions or editions are affected. Other versions or editions are either past their support life cycle or are not affected. To determine the support life cycle for your software version or edition, visit Microsoft Support Lifecycle.
Affected Software
Operating System | Component | Maximum Security Impact | Aggregate Severity Rating | Bulletins Replaced by this Update |
---|---|---|---|---|
Microsoft Windows 2000 Server Service Pack 4 | Active Directory (KB969805) |
Remote Code Execution | Critical | MS08-060 |
Windows XP Professional Service Pack 2 and Windows XP Professional Service Pack 3 | Active Directory Application Mode (ADAM) (KB970437) |
Denial of Service | Important | MS08-035 |
Windows XP Professional x64 Edition Service Pack 2 | Active Directory Application Mode (ADAM) (KB970437) |
Denial of Service | Important | MS08-035 |
Windows Server 2003 Service Pack 2 | Active Directory (KB969805) |
Denial of Service | Important | MS08-035 |
Windows Server 2003 Service Pack 2 | Active Directory Application Mode (ADAM) (KB970437) |
Denial of Service | Important | MS08-035 |
Windows Server 2003 x64 Edition Service Pack 2 | Active Directory (KB969805) |
Denial of Service | Important | MS08-035 |
Windows Server 2003 x64 Edition Service Pack 2 | Active Directory Application Mode (ADAM) (KB970437) |
Denial of Service | Important | MS08-035 |
Windows Server 2003 with SP2 for Itanium-based Systems | Active Directory (KB969805) |
Denial of Service | Important | MS08-035 |
Operating System | Component |
---|---|
Microsoft Windows 2000 Professional Service Pack 4 | Not applicable |
Windows Vista, Windows Vista Service Pack 1, and Windows Vista Service Pack 2 | Not applicable |
Windows Vista x64 Edition, Windows Vista x64 Edition Service Pack 1, and Windows Vista x64 Edition Service Pack 2 | Not applicable |
Windows Server 2008 for 32-bit Systems and Windows Server 2008 for 32-bit Systems Service Pack 2 | Active Directory Active Directory Lightweight Directory Service (AD LDS) |
Windows Server 2008 for x64-based Systems and Windows Server 2008 for x64-based Systems Service Pack 2 | Active Directory Active Directory Lightweight Directory Service (AD LDS) |
Windows Server 2008 for Itanium-based Systems and Windows Server 2008 for Itanium-based Systems Service Pack 2 | Active Directory Active Directory Lightweight Directory Service (AD LDS) |
Frequently Asked Questions (FAQ) Related to This Security Update
Where are the file information details?
Refer to the reference tables in the Security Update Deployment section for the location of the file information details.
Why does this update address several reported security vulnerabilities?
This update contains support for several vulnerabilities because the modifications that are required to address these issues are located in related files. Instead of having to install several updates that are almost the same, customers need to install this update only.
I am using an older release of the software discussed in this security bulletin. What should I do?
The affected software listed in this bulletin have been tested to determine which releases are affected. Other releases are past their support life cycle. To determine the support life cycle for your software release, visit Microsoft Support Lifecycle.
It should be a priority for customers who have older releases of the software to migrate to supported releases to prevent potential exposure to vulnerabilities. For more information about the Windows Product Lifecycle, visit Microsoft Support Lifecycle. For more information about the extended security update support period for these software versions or editions, visit Microsoft Product Support Services.
Customers who require custom support for older releases must contact their Microsoft account team representative, their Technical Account Manager, or the appropriate Microsoft partner representative for custom support options. Customers without an Alliance, Premier, or Authorized Contract can contact their local Microsoft sales office. For contact information, visit Microsoft Worldwide Information, select the country, and then click Go to see a list of telephone numbers. When you call, ask to speak with the local Premier Support sales manager. For more information, see the Windows Operating System Product Support Lifecycle FAQ.
Vulnerability Information
Severity Ratings and Vulnerability Identifiers
The following severity ratings assume the potential maximum impact of the vulnerability. For information regarding the likelihood, within 30 days of this security bulletin's release, of the exploitability of the vulnerability in relation to its severity rating and security impact, please see the Exploitability Index in the June bulletin summary. For more information, see Microsoft Exploitability Index.
Affected Software | Active Directory Invalid Free Vulnerability - CVE-2009-1138 | Active Directory Memory Leak Vulnerability - CVE-2009-1139 | Aggregate Severity Rating |
---|---|---|---|
Active Directory on Microsoft Windows 2000 Server Service Pack 4 | Critical Remote Code Execution |
Important Denial of Service |
Critical |
Active Directory Application Mode (ADAM) when installed on Windows XP Professional Service Pack 2 and Windows XP Professional Service Pack 3 | Not applicable | Important Denial of Service |
Important |
Active Directory Application Mode (ADAM) when installed on Windows XP Professional x64 Edition Service Pack 2 | Not applicable | Important Denial of Service |
Important |
Active Directory on Windows Server 2003 Service Pack 2 | Not applicable | Important Denial of Service |
Important |
Active Directory Application Mode (ADAM) when installed on Windows Server 2003 Service Pack 2 | Not applicable | Important Denial of Service |
Important |
Active Directory on Windows Server 2003 x64 Edition Service Pack 2 | Not applicable | Important Denial of Service |
Important |
Active Directory Application Mode (ADAM) when installed on Windows Server 2003 x64 Edition Service Pack 2 | Not applicable | Important Denial of Service |
Important |
Active Directory on Windows Server 2003 with SP2 for Itanium-based Systems | Not applicable | Important Denial of Service |
Important |
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/overwriteoem** | Overwrites OEM files without prompting. |
**/nobackup** | Does not back up files needed for uninstall. |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
**/extract\[:path\]** | Extracts files without starting the Setup program. |
**/ER** | Enables extended error reporting. |
**/verbose** | Enables verbose logging. During installation, creates %Windir%\\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly. |
Removing the Update
This security update supports the following setup switches.
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
Microsoft Baseline Security Analyzer
To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.
File Version Verification
Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.
- Click Start, and then click Search.
- In the Search Results pane, click All files and folders under Search Companion.
- In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
- In the list of files, right-click a file name from the appropriate file information table, and then click Properties. Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
- On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table. Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
Registry Key Verification
You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.
These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.
Windows XP Professional (all editions) with Active Directory Application Mode (ADAM)
Reference Table
The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.
Inclusion in Future Service Packs | The update for this issue will be included in a future service pack or update rollup |
Deployment | |
Installing without user intervention | For Windows XP Professional Service Pack 2 with ADAM and Windows XP Professional Service Pack 3 with ADAM: WindowsXP-KB970437-x86-ENU /quiet |
For Windows XP Professional x64 Edition Service Pack 2 with ADAM: WindowsServer2003.WindowsXP-KB970437-x64-ENU /quiet |
|
Installing without restarting | For Windows XP Professional Service Pack 2 with ADAM and Windows XP Professional Service Pack 3 with ADAM: WindowsXP-KB970437-x86-ENU /norestart |
For Windows XP Professional x64 Edition Service Pack 2 with ADAM: WindowsServer2003.WindowsXP-KB970437-x64-ENU /norestart |
|
Update log file | KB970437.log |
Further information | See the subsection, Detection and Deployment Tools and Guidance |
Restart Requirement | |
Restart required? | Yes, you must restart your system after you apply this security update. |
HotPatching | Not applicable |
Removal Information | Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%\$NTUninstallKB970437$\Spuninst folder |
File Information | See Microsoft Knowledge Base Article 970437 |
Registry Key Verification | For all supported 32-bit editions of Windows XP with ADAM: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows XP\SP4\KB970437\Filelist |
For all supported x64-based editions of Windows XP with ADAM: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows XP Version 2003\SP3\KB970437\Filelist |
Note For supported versions of Windows XP Professional x64 Edition, this security update is the same as supported versions of the Windows Server 2003 x64 Edition security update.
Deployment Information
Installing the Update
When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.
If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.
For more information about the installer, visit the Microsoft TechNet Web site.
For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.
This security update supports the following setup switches.
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/overwriteoem** | Overwrites OEM files without prompting. |
**/nobackup** | Does not back up files needed for uninstall. |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
**/integrate:path** | Integrates the update into the Windows source files. These files are located at the path that is specified in the switch. |
**/extract\[:path\]** | Extracts files without starting the Setup program. |
**/ER** | Enables extended error reporting. |
**/verbose** | Enables verbose logging. During installation, creates %Windir%\\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly. |
Removing the Update
This security update supports the following setup switches.
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
Microsoft Baseline Security Analyzer
To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.
File Version Verification
Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.
- Click Start, and then click Search.
- In the Search Results pane, click All files and folders under Search Companion.
- In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
- In the list of files, right-click a file name from the appropriate file information table, and then click Properties. Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
- On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table. Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
Registry Key Verification
You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.
These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.
Windows Server 2003 (all editions) with Active Directory
Reference Table
The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.
Inclusion in Future Service Packs | The update for this issue will be included in a future service pack or update rollup |
Deployment | |
Installing without user intervention | For all supported 32-bit editions of Windows Server 2003 with Active Directory: WindowsServer2003-KB969805-x86-ENU /quiet |
For all supported x64-based editions of Windows Server 2003 with Active Directory: WindowsServer2003.WindowsXP-KB969805-x64-ENU /quiet |
|
For all supported Itanium-based editions of Windows Server 2003 with Active Directory: WindowsServer2003-KB969805-ia64-ENU /quiet |
|
Installing without restarting | For all supported 32-bit editions of Windows Server 2003 with Active Directory: WindowsServer2003-KB969805-x86-ENU /norestart |
For all supported x64-based editions of Windows Server 2003 with Active Directory: WindowsServer2003.WindowsXP-KB969805-x64-ENU /norestart |
|
For all supported Itanium-based editions of Windows Server 2003 with Active Directory: WindowsServer2003-KB969805-ia64-ENU /norestart |
|
Update log file | KB969805.log |
Further information | See the subsection, Detection and Deployment Tools and Guidance |
Restart Requirement | |
Restart required? | Yes, you must restart your system after you apply this security update. |
HotPatching | This security update does not support HotPatching. For more information about HotPatching, see Microsoft Knowledge Base Article 897341. |
Removal Information | Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%\$NTUninstallKB969805$\Spuninst folder |
File Information | See Microsoft Knowledge Base Article 969805 |
Registry Key Verification | HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows Server 2003\SP3\KB969805\Filelist |
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/overwriteoem** | Overwrites OEM files without prompting. |
**/nobackup** | Does not back up files needed for uninstall. |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
**/integrate:path** | Integrates the update into the Windows source files. These files are located at the path that is specified in the switch. |
**/extract\[:path\]** | Extracts files without starting the Setup program. |
**/ER** | Enables extended error reporting. |
**/verbose** | Enables verbose logging. During installation, creates %Windir%\\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly. |
Removing the Update
This security update supports the following setup switches.
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
Microsoft Baseline Security Analyzer
To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.
File Version Verification
Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.
- Click Start, and then click Search.
- In the Search Results pane, click All files and folders under Search Companion.
- In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
- In the list of files, right-click a file name from the appropriate file information table, and then click Properties. Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
- On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table. Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
Registry Key Verification
You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.
These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.
Windows Server 2003 (all editions) with Active Directory Application Mode (ADAM)
Reference Table
The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.
Inclusion in Future Service Packs | The update for this issue will be included in a future service pack or update rollup |
Deployment | |
Installing without user intervention | For all supported 32-bit editions of Windows Server 2003 with ADAM: WindowsServer2003-KB970437-x86-ENU /quiet |
For all supported x64-based editions of Windows Server 2003 with ADAM: WindowsServer2003.WindowsXP-KB970437-x64-ENU /quiet |
|
Installing without restarting | For all supported 32-bit editions of Windows Server 2003 with ADAM: WindowsServer2003-KB970437-x86-ENU /norestart |
For all supported x64-based editions of Windows Server 2003 with ADAM: WindowsServer2003.WindowsXP-KB970437-x64-ENU /norestart |
|
Update log file | KB970437.log |
Further information | See the subsection, Detection and Deployment Tools and Guidance |
Restart Requirement | |
Restart required? | Yes, you must restart your system after you apply this security update. |
HotPatching | This security update does not support HotPatching. For more information about HotPatching, see Microsoft Knowledge Base Article 897341. |
Removal Information | Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%\$NTUninstallKB970437$\Spuninst folder |
File Information | See Microsoft Knowledge Base Article 970437 |
Registry Key Verification | HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows Server 2003\SP3\KB970437\Filelist |
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/overwriteoem** | Overwrites OEM files without prompting. |
**/nobackup** | Does not back up files needed for uninstall. |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
**/integrate:path** | Integrates the update into the Windows source files. These files are located at the path that is specified in the switch. |
**/extract\[:path\]** | Extracts files without starting the Setup program. |
**/ER** | Enables extended error reporting. |
**/verbose** | Enables verbose logging. During installation, creates %Windir%\\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly. |
Removing the Update
This security update supports the following setup switches.
Switch | Description |
---|---|
**/help** | Displays the command-line options. |
Setup Modes | |
**/passive** | Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds. |
**/quiet** | Quiet mode. This is the same as unattended mode, but no status or error messages are displayed. |
Restart Options | |
**/norestart** | Does not restart when installation has completed. |
**/forcerestart** | Restarts the computer after installation and force other applications to close at shutdown without saving open files first. |
**/warnrestart\[:x\]** | Presents a dialog box with a timer warning the user that the computer will restart in *x* seconds. (The default setting is 30 seconds.) Intended for use with the **/quiet** switch or the **/passive** switch. |
**/promptrestart** | Displays a dialog box prompting the local user to allow a restart. |
Special Options | |
**/forceappsclose** | Forces other programs to close when the computer shuts down. |
**/log:path** | Allows the redirection of installation log files. |
Microsoft Baseline Security Analyzer
To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.
File Version Verification
Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.
- Click Start, and then click Search.
- In the Search Results pane, click All files and folders under Search Companion.
- In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
- In the list of files, right-click a file name from the appropriate file information table, and then click Properties. Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
- On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table. Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
Registry Key Verification
You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.
These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.
Other Information
Acknowledgments
Microsoft thanks the following for working with us to help protect customers:
- Joshua J. Drake of VeriSign iDefense Labs for reporting the Active Directory Invalid Free Vulnerability (CVE-2009-1138)
- Justin Wyatt from the Beaverton School District for reporting the Active Directory Memory Leak Vulnerability (CVE-2009-1139)
Microsoft Active Protections Program (MAPP)
To improve security protections for customers, Microsoft provides vulnerability information to major security software providers in advance of each monthly security update release. Security software providers can then use this vulnerability information to provide updated protections to customers via their security software or devices, such as antivirus, network-based intrusion detection systems, or host-based intrusion prevention systems. To determine whether active protections are available from security software providers, please visit the active protections Web sites provided by program partners, listed in Microsoft Active Protections Program (MAPP) Partners.
Support
- Customers in the U.S. and Canada can receive technical support from Security Support or 1-866-PCSAFETY. There is no charge for support calls that are associated with security updates. For more information about available support options, see Microsoft Help and Support.
- International customers can receive support from their local Microsoft subsidiaries. There is no charge for support that is associated with security updates. For more information about how to contact Microsoft for support issues, visit the International Support Web site.
Disclaimer
The information provided in the Microsoft Knowledge Base is provided "as is" without warranty of any kind. Microsoft disclaims all warranties, either express or implied, including the warranties of merchantability and fitness for a particular purpose. In no event shall Microsoft Corporation or its suppliers be liable for any damages whatsoever including direct, indirect, incidental, consequential, loss of business profits or special damages, even if Microsoft Corporation or its suppliers have been advised of the possibility of such damages. Some states do not allow the exclusion or limitation of liability for consequential or incidental damages so the foregoing limitation may not apply.
Revisions
- V1.0 (June 9, 2009): Bulletin published.
- V1.1 (June 17, 2009): Listed Microsoft Windows 2000 Professional Service Pack 4, all supported editions of Windows Vista, and all supported versions of Windows Server 2008 for Itanium-based Systems as non-affected software. Also, clarified which ports are used by the Global Catalog server in the Block TCP ports workaround for CVE-2009-1139. This is an informational change only.
Built at 2014-04-18T13:49:36Z-07:00