Database Detach and Attach (SQL Server)
Applies to: SQL Server (all supported versions)
The data and transaction log files of a database can be detached and then reattached to the same or another instance of SQL Server. Detaching and attaching a database is useful if you want to change the database to a different instance of SQL Server on the same computer or to move the database.
File access permissions are set during a number of database operations, including detaching or attaching a database.
We recommend that you do not attach or restore databases from unknown or untrusted sources. Such databases could contain malicious code that might execute unintended Transact-SQL code or cause errors by modifying the schema or the physical database structure.
Before you use a database from an unknown or untrusted source, run DBCC CHECKDB on the database on a nonproduction server and also examine the code, such as stored procedures or other user-defined code, in the database.
Detaching a Database
Detaching a database removes it from the instance of SQL Server but leaves the database intact within its data files and transaction log files. These files can then be used to attach the database to any instance of SQL Server, including the server from which the database was detached.
You cannot detach a database if any of the following are true:
The database is replicated and published. If replicated, the database must be unpublished. Before you can detach it, you must disable publishing by running sp_replicationdboption.
If you cannot use sp_replicationdboption, you can remove replication by running sp_removedbreplication.
A database snapshot exists on the database.
Before you can detach the database, you must drop all of its snapshots. For more information, see Drop a Database Snapshot (Transact-SQL).
A database snapshot cannot be detached or attached.
The database is part of an Always On availability group.
The database cannot be detached until it is removed from the availability group. For more information, see Remove a primary database from an Always On availability group.
The database is being mirrored in a database mirroring session.
The database cannot be detached unless the session is terminated. For more information, see Removing Database Mirroring (SQL Server).
The database is suspect. A suspect database cannot be detached; before you can detach it, you must put it into emergency mode. For more information about how to put a database into emergency mode, see ALTER DATABASE (Transact-SQL).
The database is a system database.
Backup and Restore and Detach
Detaching a read-only database loses information about the differential bases of differential backups. For more information, see Differential Backups (SQL Server).
Responding to Detach Errors
Errors produced while detaching a database can prevent the database from closing cleanly and the transaction log from being rebuilt. If you receive an error message, perform the following corrective actions:
Reattach all files associated with the database, not just the primary file.
Resolve the problem that caused the error message.
Detach the database again.
Attaching a Database
You can attach a copied or detached SQL Server database. When you attach a SQL Server 2005 (9.x) database that contains full-text catalog files onto a SQL Server server instance, the catalog files are attached from their previous location along with the other database files, the same as in SQL Server 2005 (9.x). For more information, see Upgrade Full-Text Search.
When you attach a database, all data files (MDF and NDF files) must be available. If any data file has a different path from when the database was first created or last attached, you must specify the current path of the file.
If the primary data file being attached is read-only, the Database Engine assumes that the database is read-only.
When an encrypted database is first attached to an instance of SQL Server, the database owner must open the master key of the database by executing the following statement:
OPEN MASTER KEY DECRYPTION BY PASSWORD = 'password'. We recommend that you enable automatic decryption of the master key by executing the following statement:
ALTER MASTER KEY ADD ENCRYPTION BY SERVICE MASTER KEY. For more information, see CREATE MASTER KEY (Transact-SQL) and ALTER MASTER KEY (Transact-SQL).
The requirement for attaching log files depends partly on whether the database is read-write or read-only, as follows:
For a read-write database, you can usually attach a log file in a new location. However, in some cases, reattaching a database requires its existing log files. Therefore, it is important to always keep all the detached log files until the database has been successfully attached without them.
If a read-write database has a single log file and you do not specify a new location for the log file, the attach operation looks in the old location for the file. If it is found, the old log file is used, regardless of whether the database was shut down cleanly. However, if the old log file is not found and if the database was shut down cleanly and has no active log chain, the attach operation attempts to build a new log file for the database.
If the primary data file being attached is read-only, the Database Engine assumes that the database is read-only. For a read-only database, the log file or files must be available at the location specified in the primary file of the database. A new log file cannot be built because SQL Server cannot update the log location stored in the primary file.
Metadata Changes on Attaching a Database
When a read-only database is detached and then reattached, the backup information about the current differential base is lost. The differential base is the most recent full backup of all the data in the database or in a subset of the files or filegroups of the database. Without the base-backup information, the master database becomes unsynchronized with the read-only database, so differential backups taken thereafter may provide unexpected results. Therefore, if you are using differential backups with a read-only database, you should establish a new differential base by taking a full backup after you reattach the database. For information about differential backups, see Differential Backups (SQL Server).
On attach, database startup occurs. Generally, attaching a database places it in the same state that it was in when it was detached or copied. However, attach-and-detach operations both disable cross-database ownership chaining for the database. For information about how to enable chaining, see cross db ownership chaining Server Configuration Option.
By default and for security, the options for is_broker_enabled, is_honor_broker_priority_on and is_trustworthy_on are set to OFF whenever the database is attached. For information about how to set these options on, see ALTER DATABASE (Transact-SQL). For more information about metadata, see Manage metadata when making a database available on another server.
Backup and Restore and Attach
Like any database that is fully or partially offline, a database with restoring files cannot be attached. If you stop the restore sequence, you can attach the database. Then, you can restart the restore sequence.
Attaching a Database to Another Server Instance
A database created by a more recent version of SQL Server cannot be attached in earlier versions. This precludes the database from being physically used with an older version of the Database Engine. However, this relates to metadata state and does not affect the database compatibility level. For more information, see ALTER DATABASE Compatibility Level (Transact-SQL).
When you attach a database onto another server instance, to provide a consistent experience to users and applications, you might have to re-create some or all of the metadata for the database, such as logins and jobs, on the other server instance. For more information, see Manage metadata when making a database available on another server instance (SQL Server).
To detach a database
To attach a database
To upgrade a database using detach and attach operations
To move a database using detach and attach operations
To delete a database snapshot
Submit and view feedback for