shutdown function (winsock.h)

The shutdown function disables sends or receives on a socket.

Syntax

int shutdown(
  [in] SOCKET s,
  [in] int    how
);

Parameters

[in] s

A descriptor identifying a socket.

[in] how

A flag that describes what types of operation will no longer be allowed. Possible values for this flag are listed in the Winsock2.h header file.

Value Meaning
SD_RECEIVE
0
Shutdown receive operations.
SD_SEND
1
Shutdown send operations.
SD_BOTH
2
Shutdown both send and receive operations.

Return value

If no error occurs, shutdown returns zero. Otherwise, a value of SOCKET_ERROR is returned, and a specific error code can be retrieved by calling WSAGetLastError.

Error code Meaning
WSAECONNABORTED
The virtual circuit was terminated due to a time-out or other failure. The application should close the socket as it is no longer usable.

This error applies only to a connection-oriented socket.

WSAECONNRESET
The virtual circuit was reset by the remote side executing a hard or abortive close. The application should close the socket as it is no longer usable.

This error applies only to a connection-oriented socket.

WSAEINPROGRESS
A blocking Windows Sockets 1.1 call is in progress, or the service provider is still processing a callback function.
WSAEINVAL
The how parameter is not valid, or is not consistent with the socket type. For example, SD_SEND is used with a UNI_RECV socket type.
WSAENETDOWN
The network subsystem has failed.
WSAENOTCONN
The socket is not connected. This error applies only to a connection-oriented socket.
WSAENOTSOCK
Note  The descriptor is not a socket.
 
WSANOTINITIALISED
A successful WSAStartup call must occur before using this function.

Remarks

The shutdown function is used on all types of sockets to disable reception, transmission, or both.

If the how parameter is SD_RECEIVE, subsequent calls to the recv function on the socket will be disallowed. This has no effect on the lower protocol layers. For TCP sockets, if there is still data queued on the socket waiting to be received, or data arrives subsequently, the connection is reset, since the data cannot be delivered to the user. For UDP sockets, incoming datagrams are accepted and queued. In no case will an ICMP error packet be generated.

If the how parameter is SD_SEND, subsequent calls to the send function are disallowed. For TCP sockets, a FIN will be sent after all data is sent and acknowledged by the receiver.

Setting how to SD_BOTH disables both sends and receives as described above.

The shutdown function does not close the socket. Any resources attached to the socket will not be freed until closesocket is invoked.

To assure that all data is sent and received on a connected socket before it is closed, an application should use shutdown to close connection before calling closesocket. One method to wait for notification that the remote end has sent all its data and initiated a graceful disconnect uses the WSAEventSelect function as follows :

  1. Call WSAEventSelect to register for FD_CLOSE notification.
  2. Call shutdown with how=SD_SEND.
  3. When FD_CLOSE received, call the recv or WSARecv until the function completes with success and indicates that zero bytes were received. If SOCKET_ERROR is returned, then the graceful disconnect is not possible.
  4. Call closesocket.
Another method to wait for notification that the remote end has sent all its data and initiated a graceful disconnect uses overlapped receive calls follows :
  1. Call shutdown with how=SD_SEND.
  2. Call recv or WSARecv until the function completes with success and indicates zero bytes were received. If SOCKET_ERROR is returned, then the graceful disconnect is not possible.
  3. Call closesocket.
Note  The shutdown function does not block regardless of the SO_LINGER setting on the socket.
 

For more information, see the section on Graceful Shutdown, Linger Options, and Socket Closure.

Once the shutdown function is called to disable send, receive, or both, there is no method to re-enable send or receive for the existing socket connection.

An application should not rely on being able to reuse a socket after it has been shut down. In particular, a Windows Sockets provider is not required to support the use of connect on a socket that has been shut down.

If an application wants to reuse a socket, then the DisconnectEx function should be called with the dwFlags parameter set to TF_REUSE_SOCKET to close a connection on a socket and prepare the socket handle to be reused. When the DisconnectEx request completes, the socket handle can be passed to the AcceptEx or ConnectEx function.

If an application wants to reuse a socket, the TransmitFile or TransmitPackets functions can be called with the dwFlags parameter set with TF_DISCONNECT and TF_REUSE_SOCKET to disconnect after all the data has been queued for transmission and prepare the socket handle to be reused. When the TransmitFile request completes, the socket handle can be passed to the function call previously used to establish the connection, such as AcceptEx or ConnectEx. When the TransmitPackets function completes, the socket handle can be passed to the AcceptEx function.

Note  The socket level disconnect is subject to the behavior of the underlying transport. For example, a TCP socket may be subject to the TCP TIME_WAIT state, causing the DisconnectEx, TransmitFile, or TransmitPackets call to be delayed.
 
Note  When issuing a blocking Winsock call such as shutdown, Winsock may need to wait for a network event before the call can complete. Winsock performs an alertable wait in this situation, which can be interrupted by an asynchronous procedure call (APC) scheduled on the same thread. Issuing another blocking Winsock call inside an APC that interrupted an ongoing blocking Winsock call on the same thread will lead to undefined behavior, and must never be attempted by Winsock clients.
 

Notes for ATM

There are important issues associated with connection teardown when using Asynchronous Transfer Mode (ATM) and Windows Sockets 2. For more information about these important considerations, see the section titled Notes for ATM in the Remarks section of the closesocket function reference.

Windows Phone 8: This function is supported for Windows Phone Store apps on Windows Phone 8 and later.

Windows 8.1 and Windows Server 2012 R2: This function is supported for Windows Store apps on Windows 8.1, Windows Server 2012 R2, and later.

Requirements

Requirement Value
Minimum supported client Windows 8.1, Windows Vista [desktop apps | UWP apps]
Minimum supported server Windows Server 2003 [desktop apps | UWP apps]
Target Platform Windows
Header winsock.h (include Winsock2.h, Webhost.h)
Library Ws2_32.lib
DLL Ws2_32.dll

See also

AcceptEx

ConnectEx

DisconnectEx

TransmitFile

TransmitPackets

WSAEventSelect

Winsock Functions

Winsock Reference

connect

socket