Share via


Configure LVM on a Linux VM in Azure

This document will discuss how to configure Logical Volume Manager (LVM) in your Azure virtual machine. LVM may be used on the OS disk or data disks in Azure VMs, however, by default most cloud images will not have LVM configured on the OS disk. The steps below will focus on configuring LVM for your data disks.

Linear vs. striped logical volumes

LVM can be used to combine a number of physical disks into a single storage volume. By default LVM will usually create linear logical volumes, which means that the physical storage is concatenated together. In this case read/write operations will typically only be sent to a single disk. In contrast, we can also create striped logical volumes where reads and writes are distributed to multiple disks contained in the volume group (similar to RAID0). For performance reasons, it is likely you will want to stripe your logical volumes so that reads and writes utilize all your attached data disks.

This document will describe how to combine several data disks into a single volume group, and then create a striped logical volume. The steps below are generalized to work with most distributions. In most cases the utilities and workflows for managing LVM on Azure are not fundamentally different than other environments. As usual, also consult your Linux vendor for documentation and best practices for using LVM with your particular distribution.

Attaching data disks

One will usually want to start with two or more empty data disks when using LVM. Based on your IO needs, you can choose to attach disks that are stored in our Standard Storage, with up to 500 IO/ps per disk or our Premium storage with up to 5000 IO/ps per disk. This article will not go into detail on how to provision and attach data disks to a Linux virtual machine. See the Microsoft Azure article attach a disk for detailed instructions on how to attach an empty data disk to a Linux virtual machine on Azure.

Install the LVM utilities

  • Ubuntu

    sudo apt-get update
    sudo apt-get install lvm2
    
  • RHEL, CentOS & Oracle Linux

    sudo yum install lvm2
    
  • SLES 12 and openSUSE

    sudo zypper install lvm2
    
  • SLES 11

    sudo zypper install lvm2
    

    On SLES11, you must also edit /etc/sysconfig/lvm and set LVM_ACTIVATED_ON_DISCOVERED to "enable":

    LVM_ACTIVATED_ON_DISCOVERED="enable" 
    

Configure LVM

In this guide we will assume you have attached three data disks, which we'll refer to as /dev/sdc, /dev/sdd and /dev/sde. These paths may not match the disk path names in your VM. You can run 'sudo fdisk -l' or similar command to list your available disks.

  1. Prepare the physical volumes:

    sudo pvcreate /dev/sd[cde]
    Physical volume "/dev/sdc" successfully created
    Physical volume "/dev/sdd" successfully created
    Physical volume "/dev/sde" successfully created
    
  2. Create a volume group. In this example we are calling the volume group data-vg01:

    sudo vgcreate data-vg01 /dev/sd[cde]
    Volume group "data-vg01" successfully created
    
  3. Create the logical volume(s). The command below we will create a single logical volume called data-lv01 to span the entire volume group, but note that it is also feasible to create multiple logical volumes in the volume group.

    sudo lvcreate --extents 100%FREE --stripes 3 --name data-lv01 data-vg01
    Logical volume "data-lv01" created.
    
  4. Format the logical volume

    sudo mkfs -t ext4 /dev/data-vg01/data-lv01
    

    Note

    With SLES11 use -t ext3 instead of ext4. SLES11 only supports read-only access to ext4 filesystems.

Add the new file system to /etc/fstab

Important

Improperly editing the /etc/fstab file could result in an unbootable system. If unsure, refer to the distribution's documentation for information on how to properly edit this file. It is also recommended that a backup of the /etc/fstab file is created before editing.

  1. Create the desired mount point for your new file system, for example:

    sudo mkdir /data
    
  2. Locate the logical volume path

    lvdisplay
    --- Logical volume ---
    LV Path                /dev/data-vg01/data-lv01
    ....
    
  3. Open /etc/fstab in a text editor and add an entry for the new file system, for example:

    /dev/data-vg01/data-lv01  /data  ext4  defaults  0  2
    

    Then, save and close /etc/fstab.

  4. Test that the /etc/fstab entry is correct:

    sudo mount -a
    

    If this command results in an error message check the syntax in the /etc/fstab file.

    Next run the mount command to ensure the file system is mounted:

    mount
    ......
    /dev/mapper/data--vg01-data--lv01 on /data type ext4 (rw)
    
  5. (Optional) Failsafe boot parameters in /etc/fstab

    Many distributions include either the nobootwait or nofail mount parameters that may be added to the /etc/fstab file. These parameters allow for failures when mounting a particular file system and allow the Linux system to continue to boot even if it is unable to properly mount the RAID file system. Refer to your distribution's documentation for more information on these parameters.

    Example (Ubuntu):

    /dev/data-vg01/data-lv01  /data  ext4  defaults,nobootwait  0  2
    

TRIM/UNMAP support

Some Linux kernels support TRIM/UNMAP operations to discard unused blocks on the disk. These operations are primarily useful in standard storage to inform Azure that deleted pages are no longer valid and can be discarded. Discarding pages can save cost if you create large files and then delete them.

There are two ways to enable TRIM support in your Linux VM. As usual, consult your distribution for the recommended approach:

  • Use the discard mount option in /etc/fstab, for example:

    /dev/data-vg01/data-lv01  /data  ext4  defaults,discard  0  2
    
  • In some cases the discard option may have performance implications. Alternatively, you can run the fstrim command manually from the command line, or add it to your crontab to run regularly:

    Ubuntu

    # sudo apt-get install util-linux
    # sudo fstrim /datadrive
    

    RHEL, CentOS & Oracle Linux

    # sudo yum install util-linux
    # sudo fstrim /datadrive