Azure Stack Edge Mini R safety instructions
READ SAFETY AND HEALTH INFORMATION
Read all the safety information in this article before you use your Azure Stack Edge Mini R device, a composition of one battery pack, one AC/DC plugged power supply, one module power adapter, and one server module. Failure to follow instructions could result in fire, electric shock, injuries, or damage to your properties. Read all safety information below before using Azure Stack Edge Mini R.
Safety icon conventions
The following signal words for hazard alerting signs are:
|DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
The following hazard icons are to be observed when setting up and running your Azure Stack Edge Mini R device:
|Read All Instructions First|
|NOTICE:||Indicates information considered important, but not hazard-related.|
|Electric Shock Hazard|
|Indoor Use Only|
|No User Serviceable Parts. Do not access unless properly trained.|
Handling precautions and site selection
The Azure Stack Edge Mini R device has the following handling precautions and site selection criteria:
- Inspect the as-received device for damages. If the device enclosure is damaged, contact Microsoft Support to obtain a replacement. Do not attempt to operate the device.
- If you suspect the device is malfunctioning, contact Microsoft Support to obtain a replacement. Do not attempt to service the device.
- The device contains no user-serviceable parts. Hazardous voltage, current, and energy levels are present inside. Do not open. Return the device to Microsoft for servicing.
It is recommended to operate the system:
- Away from sources of heat including direct sunlight and radiators.
- In locations not exposed to moisture or rain.
- Located in a space that minimizes vibration and physical shock. The system is designed for shock and vibration according to MIL-STD-810G.
- Isolated from strong electromagnetic fields produced by electrical devices.
- Do not allow any liquid or any foreign object to enter the System. Do not place beverages or any other liquid containers on or near the system.
- This equipment contains a lithium battery. Do not attempt to service the battery pack. Batteries in this equipment are not user serviceable. Risk of Explosion if battery is replaced by an incorrect type.
Only charge the battery pack when it is a part of the Azure Stack Edge Mini R device, do not charge as a separate device.
- The ON/OFF switch on the battery pack is for discharging the battery to the server module only. If the power adapter is plugged into the battery pack, power is passed to the server module even if the switch is in the OFF position.
- Do not burn or short circuit the battery pack. It must be recycled or disposed of properly.
- In lieu of using the provided AC/DC power supply, this system also has the option to use a field provided Type 2590 Battery. In this case, the end user shall verify that it meets all applicable safety, transportation, environmental, and any other national/local regulations.
- When operating the system with Type 2590 Battery, operate the battery within the conditions of use specified by the battery manufacturer.
This device has two SFP+ ports, which may be used with optical transceivers. To avoid hazardous laser radiation, only use with Class 1 transceivers.
The Azure Stack Edge Mini R device has the following electrical precautions:
When used with the power supply adaptor:
Provide a safe electrical earth connection to the power supply cord. The alternating current (AC) cord has a three-wire grounding plug (a plug that has a grounding pin). This plug fits only a grounded AC outlet. Do not defeat the purpose of the grounding pin.
Given that the plug on the power supply cord is the main disconnect device, ensure that the socket outlets are located near the device and are easily accessible.
Unplug the power cord(s) (by pulling the plug, not the cord) and disconnect all cables if any of the following conditions exist:
- The power cord or plug becomes frayed or otherwise damaged.
- The device is exposed to rain, excess moisture, or other liquids.
- The device has been dropped and the device casing has been damaged.
- You suspect the device needs service or repair.
Permanently unplug the unit before you move it or if you think it has become damaged in any way.
Provide a suitable power source with electrical overload protection to meet the following power specifications:
Voltage: 100 - 240 Volts AC
Current: 1.7 Amperes
Frequency: 50 to 60 Hz
- Do not attempt to modify or use AC power cord(s) other than the ones provided with the equipment.
- Power supply labeled with this symbol is rated for indoor use only.
The following contains regulatory information for Azure Stack Edge Mini R device, regulatory model number: TMA01.
The Azure Stack Edge Mini R device is designed for use with NRTL Listed (UL, CSA, ETL, etc.), and IEC/EN 60950-1 or IEC/EN 62368-1 compliant (CE marked) Information Technology equipment.
In countries other than the USA and Canada, network cables (not provided with the equipment) shall not be installed with this equipment if their length is greater than 3 meters.
The equipment is designed to operate in the following environments:
|System temperature specifications||
|Relative humidity (RH) specifications||
|Maximum altitude specifications||
NOTICE: Changes or modifications made to the equipment not expressly approved by Microsoft may void the user's authority to operate the equipment.
CANADA and USA:
NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
The Netgear A6150 WiFi USB Adapter provided with this equipment is intended to be operated close to the human body are tested for body-worn Specific Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg when averaged over 1 g of tissue. When carrying the product or using it while worn on your body, maintain a distance of 10 mm from the body to ensure compliance with RF exposure requirements.
The Netgear A6150 WiFi USB Adapter complies with ANSI/IEEE C95.1-1999 and was tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C.
Netgear A6150 Specific Absorption Rate (SAR): 1.18 W/kg averaged over 1 g of tissue
The Netgear A6150 WiFi USB Adapter is to be used with approved antennas only. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multitransmitter product procedures. For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Users are advised that high-power radars are allocated as primary users (priority users) of the bands 5250–5350 MHz and 5650–5850 MHz, and these radars could cause interference and/or damage to LE-LAN devices.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For more information about interference issues, go to the FCC website at fcc.gov/cgb/consumerfacts/interference.html. You can also call the FCC at 1-888-CALL FCC to request Interference and Telephone Interference fact sheets.
Additional information about radiofrequency safety can be found on the FCC website at https://www.fcc.gov/general/radio-frequency-safety-0 and the Industry Canada website at http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html.
This product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, television sets, and other electronic devices.
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
Microsoft Corporation, One Microsoft Way, Redmond, WA 98052, USA
United States: (800) 426-9400
Canada: (800) 933-4750
Netgear A6150 WiFi USB Adapter FCC ID: PY318300429
Netgear A6150 WiFi USB Adapter IC ID: 4054A-18300429
The Netgear A6150 WiFi USB Adapter provided with this equipment is compliant with SAR for general population/uncontrolled exposure limits in IC RSS-102 and has been tested in accordance with the measurement methods and procedures specified in IEEE 1528. Maintain at least 10-mm distance for body-worn condition.
The Netgear A6150 WiFi USB Adapter complies with the Canada portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in its manual. Further RF exposure reduction can be achieved by keeping the product as far as possible from your body or by setting the device to a lower output power if such a function is available.
A table with the Specific Absorption Rate (SAR) averaged over 1 g for each product can be seen in the USA section above.
Request a copy of the EU Declaration of Conformity for this equipment. Send email to CSI_Compliance@microsoft.com.
The Netgear A6150 WiFi USB Adapter provided with this equipment is in compliance with Directive 2014/53/EU and can also be provided on request.
This is a class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Disposal of waste batteries and electrical and electronic equipment:
This symbol on the product or its batteries or its packaging means that this product and any batteries it contains must not be disposed of with your household waste. Instead, it is your responsibility to hand this over to an applicable collection point for the recycling of batteries and electrical and electronic equipment. This separate collection and recycling will help to conserve natural resources and prevent potential negative consequences for human health and the environment due to the possible presence of hazardous substances in batteries and electrical and electronic equipment, which could be caused by inappropriate disposal. For more information about where to drop off your batteries and electrical and electronic waste, please contact your local city/municipality office, your household waste disposal service, or the shop where you purchased this product. Contact email@example.com for additional information on WEEE.
This product contains coin cell battery(ies).
The Netgear A6150 WiFi USB Adapter provided with this equipment is intended to be operated close to the human body and is tested for body-worn Specific Absorption Rate (SAR) compliance (see below values). When carrying the product or using it while worn on your body, maintain a distance of 10mm from the body to ensure compliance with RF exposure requirements.
Netgear A6150 Specific Absorption Rate (SAR): 0.54 W/kg averaged over 10g of tissue
This device may operate in all member states of the EU. Observe national and local regulations where the device is used. This device is restricted to indoor use only when operating in the 5150-5350 MHz frequency range in the following countries:
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of Netgear wireless products for sale in the EU:
|Frequency range (MHz)||Channels used||Max Transmit Power (dBm/mW)|
|2400-2483.5||1-13||ODFM: 19.9 dBm (97.7 mW)
CCK: 17.9 dBm (61.7 mW)
|5150-5320||36-48||22.9 dBm (195 mW)|
|5250-5350||52-64||22.9 dBm (195 mW) with TPC
19.9 dBm (97.7 mW) non-TPC
|5470-5725||100-140||29.9 dBm (977 mW) with TPC
29.6 dBm (490 mW) non-TPC
Microsoft Ireland Sandyford Ind Est Dublin D18 KX32 IRL
Telephone number: +353 1 295 3826
Fax number: +353 1 706 4110
The Netgear A6150 WiFi USB Adapter provided with this equipment complies with IMDA standards.