顯示 (microsoft-windows-安裝-顯示) Display (microsoft-windows-setup-display)

Display 包含視訊卡的顯示設定。Display contains display settings for a video adapter.

Display這項設定會在 Windows 安裝程式的 Windows PE 階段使用。The Display setting is used during the Windows PE phase of the Windows installation process. 顯示設定不會套用至 Windows 安裝。The display settings are not applied to the Windows installation. 若要變更 Windows 安裝的顯示設定,請參閱在Microsoft Windows Shell 安裝程式元件中顯示To change the display settings for the Windows installation, see Display in the Microsoft-Windows-Shell-Setup component.

建議您使用預設設定。We recommend that you use the default settings. 如果您為此設定選取的值不受 Windows PE、視訊卡或顯示器所支援,則 Windows PE 可能只會顯示空白畫面,而不會顯示錯誤。If you select a value for this setting that is not supported by Windows PE, your video adapter, or the display monitor, then Windows PE might show only a blank screen without displaying an error.

注意

在 UEFI 型電腦上,除非您已在來源 boot.ini 的 Windows PE 映射中新增圖形驅動程式,否則會忽略此設定 \ \ 。On UEFI-based computers, this setting is ignored unless you have added a graphics driver into the Windows PE image at \sources\boot.wim. 在 BIOS 型電腦上,根據預設,Windows PE 會使用1024x768 的解析度。On BIOS-based computers, by default, Windows PE uses a resolution of 1024x768. 針對解析度較低的顯示器,Windows PE 會根據所連接顯示器的擴充顯示器顯示識別資料 (EDID) ,使用可用的最大解析度。For displays with a smaller maximum resolution, Windows PE uses the largest resolution available, based on the extended display identification data (EDID) of the connected display.

子元素Child Elements

設定Setting DescriptionDescription
ColorDepthColorDepth 指定要套用至顯示裝置的色彩深度。Specifies the color depth to apply to the display device.
HorizontalResolutionHorizontalResolution 指定要套用至顯示裝置的水準解析度。Specifies the horizontal resolution to apply to the display device.
RefreshRateRefreshRate 指定要套用至顯示裝置的更新頻率。Specifies the refresh rate to apply to the display device.
VerticalResolutionVerticalResolution 指定要套用至顯示裝置的垂直解析度。Specifies the vertical resolution to apply to the display device.

有效的設定階段Valid Configuration Passes

windowsPEwindowsPE

父階層Parent Hierarchy

microsoft-windows-設定- | 顯示microsoft-windows-setup- | Display

套用至Applies To

此設定只會影響 BIOS 電腦上的 Windows 安裝程式處理常式。This setting only affects the Windows Setup process on BIOS-based computers. 以 UEFI 為基礎的電腦不會受到這些設定的影響。UEFI-based computers are not affected by these settings.

如需此元件所支援的 Windows 版本和架構清單,請參閱 Microsoft Windows 安裝程式For the list of the Windows editions and architectures that this component supports, see Microsoft-Windows-Setup.

XML 範例XML Example

下列 XML 輸出會將顯示器解析度設定為1920x1080,16位色深度和更新率為60赫茲。The following XML output sets the display resolution to 1920x1080, with 16-bit color depth and a refresh rate of 60 hertz.

<Display>
   <HorizontalResolution>1920</HorizontalResolution>
   <VerticalResolution>1080</VerticalResolution>
   <ColorDepth>16</ColorDepth>
   <RefreshRate>60</RefreshRate>
</Display>

Microsoft-Windows-SetupMicrosoft-Windows-Setup