Azure AD Connect: Upgrade from a previous version to the latest

This topic describes the different methods that you can use to upgrade your Azure Active Directory (Azure AD) Connect installation to the latest release. We recommend that you keep yourself current with the releases of Azure AD Connect. You also use the steps in the Swing migration section when you make a substantial configuration change.

If you want to upgrade from DirSync, see Upgrade from Azure AD sync tool (DirSync) instead.

There are a few different strategies that you can use to upgrade Azure AD Connect.

Method Description
Automatic upgrade This is the easiest method for customers with an express installation.
In-place upgrade If you have a single server, you can upgrade the installation in-place on the same server.
Swing migration With two servers, you can prepare one of the servers with the new release or configuration, and change the active server when you're ready.

For permissions information, see the permissions required for an upgrade.

Note

After you've enabled your new Azure AD Connect server to start synchronizing changes to Azure AD, you must not roll back to using DirSync or Azure AD Sync. Downgrading from Azure AD Connect to legacy clients, including DirSync and Azure AD Sync, isn't supported and can lead to issues such as data loss in Azure AD.

In-place upgrade

An in-place upgrade works for moving from Azure AD Sync or Azure AD Connect. It doesn't work for moving from DirSync or for a solution with Forefront Identity Manager (FIM) + Azure AD Connector.

This method is preferred when you have a single server and less than about 100,000 objects. If there are any changes to the out-of-box sync rules, a full import and full synchronization occur after the upgrade. This method ensures that the new configuration is applied to all existing objects in the system. This run might take a few hours, depending on the number of objects that are in scope of the sync engine. The normal delta synchronization scheduler (which synchronizes every 30 minutes by default) is suspended, but password synchronization continues. You might consider doing the in-place upgrade during a weekend. If there are no changes to the out-of-box configuration with the new Azure AD Connect release, then a normal delta import/sync starts instead.
In-place upgrade

If you've made changes to the out-of-box synchronization rules, then these rules are set back to the default configuration on upgrade. To make sure that your configuration is kept between upgrades, make sure that you make changes as they're described in Best practices for changing the default configuration.

Swing migration

If you have a complex deployment or many objects, it might be impractical to do an in-place upgrade on the live system. For some customers, this process might take multiple days--and during this time, no delta changes are processed. You can also use this method when you plan to make substantial changes to your configuration and you want to try them out before they're pushed to the cloud.

The recommended method for these scenarios is to use a swing migration. You need (at least) two servers--one active server and one staging server. The active server (shown with solid blue lines in the following picture) is responsible for the active production load. The staging server (shown with dashed purple lines) is prepared with the new release or configuration. When it's fully ready, this server is made active. The previous active server, which now has the old version or configuration installed, is made into the staging server and is upgraded.

The two servers can use different versions. For example, the active server that you plan to decommission can use Azure AD Sync, and the new staging server can use Azure AD Connect. If you use swing migration to develop a new configuration, it's a good idea to have the same versions on the two servers.
Staging server

Note

Some customers prefer to have three or four servers for this scenario. When the staging server is upgraded, you don't have a backup server for disaster recovery. With three or four servers, you can prepare one set of primary/standby servers with the new version, which ensures that there is always a staging server that's ready to take over.

These steps also work to move from Azure AD Sync or a solution with FIM + Azure AD Connector. These steps don't work for DirSync, but the same swing migration method (also called parallel deployment) with steps for DirSync is in Upgrade Azure Active Directory sync (DirSync).

Use a swing migration to upgrade

  1. If you use Azure AD Connect on both servers and plan to only make a configuration change, make sure that your active server and staging server are both using the same version. That makes it easier to compare differences later. If you're upgrading from Azure AD Sync, then these servers have different versions. If you're upgrading from an older version of Azure AD Connect, it's a good idea to start with the two servers that are using the same version, but it's not required.
  2. If you've made a custom configuration and your staging server doesn't have it, follow the steps under Move a custom configuration from the active server to the staging server.
  3. If you're upgrading from an earlier release of Azure AD Connect, upgrade the staging server to the latest version. If you're moving from Azure AD Sync, then install Azure AD Connect on your staging server.
  4. Let the sync engine run full import and full synchronization on your staging server.
  5. Verify that the new configuration didn't cause any unexpected changes by using the steps under "Verify" in Verify the configuration of a server. If something isn't as expected, correct it, run the import and sync, and verify the data until it looks good, by following the steps.
  6. Switch the staging server to be the active server. This is the final step "Switch active server" in Verify the configuration of a server.
  7. If you're upgrading Azure AD Connect, upgrade the server that's now in staging mode to the latest release. Follow the same steps as before to get the data and configuration upgraded. If you upgraded from Azure AD Sync, you can now turn off and decommission your old server.

Move a custom configuration from the active server to the staging server

If you've made configuration changes to the active server, you need to make sure that the same changes are applied to the staging server. To help with this move, you can use the Azure AD Connect configuration documenter.

You can move the custom sync rules that you've created by using PowerShell. You must apply other changes the same way on both systems, and you can't migrate the changes. The configuration documenter can help you comparing the two systems to make sure they are identical. The tool can also help in automating the steps found in this section.

You need to configure the following things the same way on both servers:

  • Connection to the same forests
  • Any domain and OU filtering
  • The same optional features, such as password sync and password writeback

Move custom synchronization rules
To move custom synchronization rules, do the following:

  1. Open Synchronization Rules Editor on your active server.
  2. Select a custom rule. Click Export. This brings up a Notepad window. Save the temporary file with a PS1 extension. This makes it a PowerShell script. Copy the PS1 file to the staging server.
    Sync rule export
  3. The Connector GUID is different on the staging server, and you must change it. To get the GUID, start Synchronization Rules Editor, select one of the out-of-box rules that represent the same connected system, and click Export. Replace the GUID in your PS1 file with the GUID from the staging server.
  4. In a PowerShell prompt, run the PS1 file. This creates the custom synchronization rule on the staging server.
  5. Repeat this for all your custom rules.

Next steps

Learn more about integrating your on-premises identities with Azure Active Directory.